View MB3892_869002.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

FUJITSU SEMICONDUCTOR DATA SHEET
DS04-27802-1E
ASSP For Power Management Applications (Mobile Phones)
Power Management IC for Mobile Phone
MB3892
s DESCRIPTION
MB3892 is a low-saturation voltage type series regulator contains 3 channels for the baseband regulator, 1 channel for the backup regulator, 6 channels for the RF regulator, and 1 channel for the variable regulator. MB3892 is built in reset circuit, serial control circuit, operation Amp. for charge control of Lithium ion battery, LED drive circuit, receiver Amp., loudspeaker drive Amp., sounder circuit, vibrator drive circuit, and 4-ch D/A converter and the devices is miniaturized by systematization of built-in power supply for mobile phone.
s FEATURES
* Power supply voltage range * * * * * * : VB = 2.85 V to 5.5 V : EXTVCC = 3.0 V to 6.5 V : 100 A (Max.)
Low power consumption current during standby Built-in low-saturation voltage type series regulator Built-in power-on reset function Built-in serial control function Built-in operation Amp. for charge control of Lithium ion battery Special power off function (To prevent battery discharge, this function controls the power consumption current of main IC under 11 A (typ.) on the shipment.)
s PACKAGE
80-pin plastic LQFP
(FPT-80P-M17)
MB3892
s PIN ASSIGNMENT
(TOP VIEW)
Power control + Charge control
60 : D/AOUT4 59 : IPOFF 58 : VB4 57 : VBDET 56 : 3VDET 55 : GND6 54 : EXTS 53 : VA 52 : EXTVCC 51 : CHGDET 50 : CHGOUT 49 : CHGV 48 : BATT 47 : CHGI 46 : VBH 45 : VB3 44 : CHGBAT 43 : GND5 42 : RFOUT1 41 : RFCTL1
D/A
RFREG1 to RFREG4, RFREG6
D/AOUT3 : 61 D/AOUT2 : 62 D/AOUT1 : 63 GND7 : 64 D/AREF : 65
Variable REG BATTREG BBREG3 BBREG2 BBREG1 Reset VIBREG
GND8 : 66 VREGIN : 67 VREGOUT : 68 BATTOUT : 69 VB5 : 70 OUT3 : 71 OUT2-1 : 72 OUT2-2 : 73 VB6 : 74 OUT1 : 75 CTP : 76 RESET : 77 VIBREG-1 : 78 VIBREG-2 : 79 VB7 : 80
40 : RFOUT2 39 : RFCTL2 38 : RFOUT3 37 : RFCTL3 36 : RFCTL4 35 : RFOUT4 34 : VB2 33 : RFOUT6 32 : RFCTL6 31 : RFCTL5 30 : RFOUT5-1 29 : RFOUT5-2 28 : VB1 27 : VREF 26 : OUTB 25 : OUTA 24 : GND4 23 : SPOUTB 22 : SPOUTA 21 : V30R
RFREG5
LED drive
2
Serial control
(FPT-80P-M17)
Sounder
Reset
LEDR : 1 LEDO1 : 2 GND1 : 3 LEDO2 : 4 RESETIN : 5 DAT : 6 SCLK : 7 STBIN : 8 GND2 : 9 IN1 : 10 IN2 : 11 IN3 : 12 VO3 : 13 VO2 : 14 GND3 : 15 VO1 : 16 N.C. : 17 BP : 18 IN : 19 FB : 20
Receiver Amp. Loudspeaker Amp.
MB3892
s PIN DESCRIPTION
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Symbol LEDR LEDO1 GND1 LEDO2 RESETIN DAT SCLK STBIN GND2 IN1 IN2 IN3 VO3 VO2 GND3 VO1 N.C. BP IN FB V30R SPOUTA SPOUTB GND4 OUTA OUTB VREF VB1 RFOUT5-2 RFOUT5-1 RFCTL5 RFCTL6 RFOUT6 VB2 I/O O O O I I I I I I I O O O I I O O O O O O O I I O Descriptions LEDR output pin. (an open collector output) LED1 output pin. (an open drain output) Ground pin. LED2 output pin. (an open drain output) Reset detect comparator input pin. Serial data input pin. Serial clock input pin. Strobe input pin. Ground pin. Sounder1 control input pin. Sounder2 control input pin. Sounder3 control input pin. Sounder3 control output pin. (an open drain output) Sounder2 control output pin. (an open drain output) Ground pin. Sounder1 control output pin. (an open drain output) No connection pin. Bypass pin. Non-inverted input pin. Inverted input pin. Power supply pin for speaker Amp. Output A pin for loudspeaker Amp. Output B pin for loudspeaker Amp. Ground pin. Output A pin for receiver Amp. Output B pin for receiver Amp. Reference output voltage pin. Power supply pin. RF REG5 output pin2. (Short circuiting to pin 30) RF REG5 output pin1. (Short circuiting to pin 29) RF REG5 control pin. RF REG6 control pin. RF REG6 output pin. Power supply pin.
(Continued)
3
MB3892
Pin No. 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68
Symbol RFOUT4 RFCTL4 RFCTL3 RFOUT3 RFCTL2 RFOUT2 RFCTL1 RFOUT1 GND5 CHGBAT VB3 VBH CHGI BATT CHGV CHGOUT CHGDET EXTVCC VA EXTS GND6 3VDET VBDET VB4 IPOFF D/AOUT4 D/AOUT3 D/AOUT2 D/AOUT1 GND7 D/AREF GND8 VREGIN VREGOUT
I/O O I I O I O I O I O O I O O I O O I I O O O O I I O RF REG4 output pin. RF REG4 output pin. RF REG3 control pin. RF REG3 output pin. RF REG2 control pin. RF REG2 output pin. RF REG1 control pin. RF REG1 output pin. Ground pin. Main charge pin. Power supply pin. Main charge pin. Main charge pin. A/D input pin. Main charge pin. Main charge pin. Main charge pin.
Descriptions
Power supply pin for charge control. Preliminary charge pin. Preliminary charge pin. Ground pin. Power supply detector pin. Power supply detector pin. Power supply pin. Special power off input pin. 10 bit D/A output pin. 8 bit D/A3 output pin. 8 bit D/A2 output pin. 8 bit D/A1 output pin. Ground pin. D/A reference voltage input pin. Ground pin. Variable REG reference voltage input pin. Variable REG output pin.
(Continued)
4
MB3892
(Continued) Pin No.
69 70 71 72 73 74 75 76 77 78 79 80
Symbol BATTOUT VB5 OUT3 OUT2-1 OUT2-2 VB6 OUT1 CTP RESET VIBREG-1 VIBREG-2 VB7
I/O O O O O O I O O O Backup REG output pin. Power supply pin. Baseband REG3 output pin.
Descriptions
Baseband REG2 output pin. (Short circuiting to pin 73) Baseband REG2 output pin. (Short circuiting to pin 72) Power supply pin. Baseband REG1output pin. Setting pin for power-on reset hold time. Reset output pin. Vibrator REG output pin. (Short circuiting to pin 79) Vibrator REG output pin. (Short circuiting to pin 78) Power supply pin.
5
6
MB3892
VB4
D/AOUT1 VA
63 62 61 60 64 RFREG1
Special power OFF
D/AOUT2
D/AOUT3
D/AOUT4
67 65 100 k GND8 66 VREGOUT (10 mA) 68 Variable REG 10 F EXBGR 100 k RFREG2
Power control
59 58 55 57 56 54 53 52 51 50 49 48 47 46 44 45 43 34 28
Charge control (Power by EXTVCC)
100 k RFREG3 100 k
CHGOUT
CHGDET
CHGBAT
EXTVCC
VREGIN D/AREF VBDET 3VDET IPOFF CHGV GND7 GND6 GND5 EXTS BATT CHGI VBH VB3 VB2 VB1 VREF RFOUT1 (2.85 V/10 mA) 42 2.2 F 41 RFCTL1
BATTOUT (3.1 V) BATTREG
s BLOCK DIAGRAM (General)
10 F BBREG3
69
1 k
D/A x 4 ch Power by BBREG1
To each REG
RFOUT2 (2.85 V/20 mA) 40 2.2 F 39 RFCTL2
OUT3 (2.85 V/60 mA)
71
2.2 F BBREG2
RFOUT3 (2.85 V/20 mA) 38 2.2 F 37 RFCTL3 RFOUT4 (2.85 V/60 mA) 35 3.3 F 36 RFCTL4
RFREG4
VB5 70 OUT2 (2.85 V/150 mA) OUT2-1 72 10 F 73 OUT2-2 76 CTP 0.1 F RESET 77
To each REG
Reset circuit Power by BBREG1
BGR
100 k
RFREG5 100 k RFREG6 1 k
VB6 74 BBREG1
Temperature protection
RFOUT5-1 30 RFOUT5 (2.85 V/200 mA) 29 RFOUT5-2 3.3 F 31 RFCTL5 RFOUT6 (2.85 V/50 mA) 33 4.7 F 32 RFCTL6 100 k
OUT1 (2.85 V/110 mA)
75
2.2 F
Sounder
VIBREG
To each REG
VB7 80 VIBREG (1.5 V/200 mA) VIBREG-1 78 10 F 79 VIBREG-2 LEDR 1
LED drive
Receiver Amp.
Serial control Power by REG1 Reset at reset circuit/ Temperature protection
LEDO1 2
LEDO2 4
GND1 3 5 8 STBIN DAT SCLK GND2 9 6 7 10 11 12 IN1 IN2 IN3 15 GND3 13 14 16 VO3 VO2 VO1 21 18 20 19 IN FB BP V30R
Loudspeaker Amp.
VREF (1.23 V) 27 1 F OUTB 26 0.1 F OUTA 25 GND4 0.1 F 24 SPOUTB 23 0.1 F SPOUTA 22 0.1 F 15 k OUT2 4.7 F 15 k 4.7 k
N.C.
RESETIN
17
ADP CPU
+ -
* Charge control
A/D
+
-
58
VB4 57 56 53 54 52 49 44
VBDET
3VDET
EXTS
VA
EXTVCC
CHGDET CHGOUT 51 50 CHGV CHGBAT
100 k 100 k SW1 47 k 6.2 k 200 k 4.7 k + - VREF 546 k 2.5 k LEDR 490 k SW5 2.5 k + - SW7 CHGI 47 A/D 100 k SW2 SW4 12.5 k 7.5 k 47 k 20 k + - - + 3VDET + - 33 k SW3 50 k 50 k 33 k SW6 VB3 45 VBH 46 BATT 48
725 k + - VREF
490 k
SW Condition chart
Other condition
SW
Serial signal data
SW1 H : OFF Special power off : OFF PRCHGOFF SW2 L : ON VB 4 V detector : OFF
SW3 SW4 BIASSW SW5
H : OFF Special power off : OFF L : ON No EXTVCC : OFF
SW6 BIASSW
H : OFF Special power off : OFF L : ON
MB3892
SW7 CHGISEL
H : ON L : OFF
7
MB3892
* Speaker Amp.
ON/ OFF
PDSP PDRCV
BIAS PDSP CHOISE L HL H
BP 18 4.7 F + -
18 k 5 k 24 k 30 k 30 k + - + - OUTB 26 10 k
Receiver Amp.
10 k 25 OUTA
32
PDSP IN 19 L 5 k H 30 k FB 20 L H 30 k
+ -
SPOUTB 23 10 k
Loudspeaker Amp.
+ - 10 k 22 SPOUTA Rfb Rfb
8
BUZZSEL
Rin
Cin
PDRCV L H H L L H
PDSP CHOISE BUZZSEL L L L H H H x H L H L x x L L L H L
Operating Amp. Receiver Amp. Receiver Amp. Standby
Operation mode Receiver (BTL drive) Earphone mode (single drive)
Loudspeaker Amp. Loudspeaker Amp. (BTL drive) Loudspeaker Amp. Short wave form output (open collector) When both of PDRCV/PDSP is "H" level, Loudspeaker Amp. the operation of loudspeaker Amp. has priority.
8
MB3892
s ABSOLUTE MAXIMUM RATINGS
Parameter Power supply voltage Symbol VB EXTVCC IO Baseband regulator output current Receiver Amp. output current Loudspeaker Amp. output current Vibrator regulator output current IO IO IO IO IO IO IO RF regulator output current IO IO IO IO Variable regulator output current Power dissipation Storage temperature IO PD Tstg Conditions BBREG1 BBREG2 BBREG3 RFREG1 RFREG2 RFREG3 RFREG4 RFREG5 RFREG6 Ta +25 C Rating Min. -55 Max. 7 7 -110 -150 -60 150 400 -200 -10 -20 -20 -60 -200 -50 -15 1420 * +125 Unit V V mA mA mA mA mA mA mA mA mA mA mA mA mA mW C
*: The packages are mounted on the dual-sided epoxy board(10 cm x 10 cm) WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
9
MB3892
s RECOMMENDED OPERATING CONDITIONS
Parameter Symbol VB Power supply voltage REG capacitor ESR guarantee value Operating ambient temperature EXTVCC RESR Ta Conditions Under 4.5 V preliminary charge circuit is not operated normally Value Min. 2.85 3.0 0.4 -30 Typ. +25 Max. 5.5 6.5 7 +80 Unit V V C
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand.
10
MB3892
s ELECTRICAL CHARACTERISTICS
* Power control (Ta = +25 C, VB = 3.6 V) Value Unit Min. Typ. Max. 1.19 2.79 2.79 -30 2.79 2.79 -30 2.79 2.79 -30 1.23 2.85 2.85 -50* 30 2.85 2.85 -50* 2.85 2.85 -50* 0 1.27 2.91 2.91 20 0 43 60 2.91 2.91 20 0 190 2.91 2.91 20 0 1 105 V V V mV mV dB A s V V mV mV dB s V V mV mV dB A s
Parameter Reference voltage Reference voltage Output voltage Line regulation Load regulation Baseband regulator [BBREG1] Ripple rejection Reverse current Rise time Output voltage Line regulation Baseband regulator Load regulation [BBREG2] Ripple rejection
Symbol VREF VO1 VOLD1 Line Load R.R
Pin No. 27 75 75 75 75 75
Conditions VREF = 0 mA OUT1 = 0 mA OUT1 = -110 mA VB = 3.1 to 4.8 V, OUT1 = -10 mA OUT1 = 0 to -110 mA Vin = 0.2 Vrms, f = 1 kHz, OUT1 = -10 mA VB = 0 to 5 V or VB = Open OUT1 = 2.2 F, OUT1 = 27 OUT2 = 0 mA OUT2 = -150 mA VB = 3.1 to 4.8 V, OUT2 = -10 mA OUT2 = 0 to -150 mA Vin = 0.2 Vrms, f = 1 kHz, OUT2 = -10 mA OUT2 = 10 F, OUT2 = 20 OUT3 = 0 mA OUT3 = -60 mA VB = 3.1 to 4.8 V, OUT3 = -10 mA OUT3 = 0 to -60 mA Vin = 0.2 Vrms, f = 1 kHz, OUT3 = -10 mA VB = 0 to 5 V or VB = Open OUT3 = 2.2 F, OUT3 = 47
IREV TR VO2 VOLD2 Line Load R.R
75 75 72, 73 72, 73 72, 73 72, 73 72, 73
Rise time Output voltage Line regulation Load regulation Baseband regulator [BBREG3] Ripple rejection Reverse current Rise time * : Standard design value
TR VO3 VOLD3 Line Load R.R
72, 73 71 71 71 71 71
IREV TR
71 71
(Continued)
11
MB3892
(Ta = +25 C, VB = 3.6 V) Value Unit Min. Typ. Max. 3.00 1.44 1.38 2.79 2.79 -30 2.79 2.79 -30 2.79 2.79 -30 3.10 -3.1 0 1.50 1.50 2.85 2.85 -55* 2.85 2.85 -55* 2.85 2.85 -55* 3.20 1 1.56 1.56 2.91 2.91 20 0 630 2.91 2.91 20 0 315 2.91 2.91 20 0 315 V mA A V V V V mV mV dB s V V mV mV dB s V V mV mV dB s
Parameter Output voltage Backup Output current regulator [BATTREG] Reverse current Vibrator drive circuit Output voltage [VIBREG] Output voltage Line regulation RF regulator Load regulation [RFREG1] Ripple rejection
Symbol Pin No. VBATT IBATT IREV VO VOLD VO1 VOLD1 Line Load R.R 69 69 69 78, 79 78, 79 42 42 42 42 42
Conditions BATTOUT = 0 mA BATTOUT = 0 V VB = 0 to 5 V or VB = Open VIBREG = 0 mA VIBREG = -200 mA RFOUT1 = 0 mA RFOUT1 = -10 mA VB = 3.1 to 4.8 V, RFOUT1 = -10 mA RFOUT1 = 0 to -10 mA Vin = 0.2 Vrms, f = 1 kHz, RFOUT1 = -10 mA RFOUT1 = 2.2 F, RFOUT1 = 300 RFOUT2 = 0 mA RFOUT2 = -20 mA VB = 3.1 to 4.8 V, RFOUT2 = -10 mA RFOUT2 = 0 to -20 mA Vin = 0.2 Vrms, f = 1 kHz, RFOUT2 = -10 mA RFOUT2 = 2.2 F, RFOUT2 = 150 RFOUT3 = 0 mA RFOUT3 = -20 mA VB = 3.1 to 4.8 V, RFOUT3 = -10 mA RFOUT3 = 0 to -20 mA Vin = 0.2 Vrms, f = 1 kHz, RFOUT3 = -10 mA RFOUT3 = 2.2 F, RFOUT3 = 150
Rise time Output voltage Line regulation RF regulator Load regulation [RFREG2] Ripple rejection
TR VO2 VOLD2 Line Load R.R
42 40 40 40 40 40
Rise time Output voltage Line regulation RF regulator Load regulation [RFREG3] Ripple rejection
TR VO3 VOLD3 Line Load R.R
40 38 38 38 38 38
Rise time * : Standard design value
TR
38
(Continued)
12
MB3892
(Ta = +25 C, VB = 3.6 V) Parameter Output voltage Line regulation RF regulator Load regulation [RFREG4] Ripple rejection Symbol Pin No. VO4 VOLD4 Line Load R.R 35 35 35 35 35 Conditions RFOUT4 = 0 mA RFOUT4 = -60 mA VB = 3.1 to 4.8 V, RFOUT4 = -10 mA RFOUT4 = 0 to -60 mA Vin = 0.2 Vrms, f = 1 kHz, RFOUT4 = -10 mA RFOUT4 = 3.1 F, RFOUT4 = 51 RFOUT5 = 0 mA RFOUT5 = -200 mA VB = 3.1 to 4.8 V, RFOUT5 = -10 mA RFOUT5 = 0 to -200 mA Vin = 0.2 Vrms, f = 1 kHz, RFOUT5 = -10 mA RFOUT5 = 3.3 F, RFOUT5 = 15 RFOUT6 = 0 mA RFOUT6 = -50 mA VB = 3.1 to 4.8 V, RFOUT6 = -10 mA RFOUT6 = 0 to -50 mA Vin = 0.2 Vrms, f = 1 kHz, RFOUT6 = -10 mA RFOUT6 = 4.7 F, RFOUT6 = 62 Value Min. 2.79 2.79 -30 2.79 2.79 -30 2.79 2.79 -30 Typ. 2.85 2.85 -55* 2.85 2.85 -55* 2.85 2.85 -55* Max. 2.91 2.91 20 0 160 2.91 2.91 20 0 50 2.91 2.91 20 0 270 Unit V V mV mV dB s V V mV mV dB s V V mV mV dB s
Rise time Output voltage Line regulation RF regulator Load regulation [RFREG5] Ripple rejection
TR VO5 VOLD5 Line Load R.R
35 29, 30 29, 30 29, 30 29, 30 29, 30
Rise time Output voltage Line regulation RF regulator Load regulation [RFREG6] Ripple rejection
TR VO6 VOLD6 Line Load R.R
29, 30 33 33 33 33 33
Rise time * : Standard design value
TR
33
(Continued)
13
MB3892
(Continued)
Parameter Symbol VIL Input voltage RF regulator control Input current IIH Input voltage range Output voltage range VIN VO VOP IO IIL IIH VIH IIL Pin No. 41, 39, 37, 36, 31, 32 41, 39, 37, 36, 31, 32 Conditions (Ta = +25 C, VB = 3.6 V) Value Unit Min. Typ. Max. 0 OUT1 x 0.7 -1 22 1.67 2.00 -2.5 -10 -1 22 -12 -9 -7 -4 -1.0 0.5 28.5 28.5 OUT1 x 0.3 OUT1 1 41 2.38 2.85 2.5 1 41 8 10 +12 +9 +7 +4 +1.0 2.5 20 -77.8 V V A A V V % mA A A bit bit LSB LSB LSB
41, 39, 37, RFCTL1 to RFCTL6 36, 31, 32 = 0 V 41, 39, 37, RFCTL1 to RFCTL6 36, 31, 32 = 2.85 V 67 68 68 68 67 67 60 60 60 VREGIN = 0 V VREGIN = 2.85 V D/A4 D/A4 (Input code is 200) D/A4 (Input code is 100, and 300) D/A4 (Input code is 080, 180, 280, and 380)
Variable bias Output voltage regulator [VARREG] precision Output current Input current System resolution
63, 62, 61 D/A1 to D/A3
D/A converter
Differential non-linear type linearity error
60 LE
D/A1 to D/A3 (Input 63, 62, 61 code is 040, 080, and 0C0) 63, 62, 61, Other input code 60
LSB
LSB V s dBm
Output voltage range Rise time Output Noise
VOC TR VNOVL
63, 62, 61, D/AOUT1 to D/AOUT4 60 = -330 A to 1 mA 63, 62, 61, D/AOUT1 to D/AOUT4 60 = 100 pF 63, 62, 61, 60
14
MB3892
(Continued)
Parameter Detected voltage Output voltage POR hold time Rise time Fall time Supply voltage detector Detected voltage Symbol VSL1 VSH1 VOH VOH TPR TR TF V3VDH V3VDL IB1 Pin No. 75 75 77 77 77 77 77 56 56 Conditions RESET = -200 A RESET = 200 A CTP 0.1 F RESET = 50 pF RESET = 50 pF (Ta = +25 C, VB = 3.6 V) Value Unit Min. Typ. Max. 2.63 2.695 OUT1 - 0.3 25 2.99 2.79 2.685 2.75 OUT1 0.01 70 3.05 2.85 11 2.74 2.805 0.4 115 500 500 3.11 2.907 20 V V V V ms ns ns V V A
Power-on reset
28, 34, 45, 58, 70, 74, Special power off 80 28, 34, 45, 58, 70, 74, Standby 80 28, 34, 45, Power on 58, 70, 74, (waiting) intermittent 80 28, 34, 45, Power on (waiting) 58, 70, 74, receiving 80 28, 34, 45, Power on (conversa58, 70, 74, tion) transmission 80 28, 34, 45, Power on (conversa58, 70, 74, tion) receiving 80
IB2
50
70
100
A
Power control (General)
Power consumption current
IB3
50
70
100
A
IB4
190
250
360
A
IB5
170
220
315
A
IB6 * : Standard design value
190
250
360
A
Note: IB1 to IB6 of general power control means the total current at VB1 to VB7 terminals the load current is not included. As for the condition of each regulators at the measurement of power consumption current , please refer to "s CONDITIONS of EACH REGURATORS at MEASUREMENT of CONSUMPTION CURRENT".
15
MB3892
* Speaker Amp. (Ta = +25 C, VB = V30R = 3.6 V, f = 1 kHz) Value Conditions Unit Min. Typ. Max. Single drive, INV input FB = 4.7 k, FB to OUTA = 15 k 8.1 10.1 12.1 dB
Parameter
Symbol Pin No.
AV1 Voltage gain AV2 Open-ended voltage gain AVO PO1 Receiver Amp. Output power PO2 Output voltage Offset voltage between output Total harmonic distorition rate Ripple rejection Rise time Voltage gain Open-ended voltage gain VO VOO THD R.R TR AV AVO PO1 Output power Loud speaker Amp. Output voltage Offset voltage between output Overall harmonic distorition rate Ripple rejection Rise time Speaker Amp. Input impedance Standby supply current PO2 VO VOO THD R.R TR RIN ICC1
25
BTL drive, INV input 25, 26 FB = 4.7 k, FB to OUTA = 15 k 25, 26 f 100 Hz V30R = 3.6 V, 25, 26 OUTA to OUTB = 32 , THD = 10% V30R = 2.85 V, 25, 26 OUTA to OUTB = 32 , THD = 10% 25, 26 OUTA to OUTB = no load 25, 26 25, 26 PO = 25 mW 25, 26
14.1 60
16.1 80* 90
18.1
dB dB mW
30 3.8 -50 14.1 160 50 3.8 -50
45 5.5 0.5 -45* 16.1 80* 260 110 5.5 0.5 -45* 30 0
50 1.0 0.1 18.1 50 1.0 0.1 50 10
mW V mV % dB s dB dB mW mW V mV % dB s k A
25, 26 BP = 1 V, BP = 4.7 F BTL drive, INV input 22, 23 FB = 4.7 k, FB to SPOUTA = 15 k 22, 23 f 100 Hz 22, 23 V30R = 3.6 V, SPOUTA to SPOUTB = 8 , THD = 10%
V30R = 2.85 V, SPOUTA to 22, 23 SPOUTB = 8 , THD = 10% 22, 23 SPOUTA to SPOUTB = no load 22, 23 22, 23 PO = 60 mW 22, 23 19, 20 21
20
22, 23 BP = 1 V, BP = 4.7 F
* : Standard design value 16
MB3892
* Sounder (Ta = +25 C, VB = 3.6 V) Value Unit Min. Typ. Max. VB x 0.7 0.0 -1 -1 0.3 0.3 0.3 0.5 0.5 0.5 10 VB VB x 0.3 1 1 V V V A V V A A
Parameter
Symbol VO1
Pin No. 16 14 13
Conditions VO1 = 200 mA VO2 = 100 mA VO3 = 50 mA
Output voltage Output leakage current Sounder Conditions for input ON
VO2 VO3 ILEAK VON VOFF IIH IIL
16, 14, 13 VB = VO1 to VO3 = 6 V 10, 11, 12 10, 11, 12
Input current
10, 11, 12 IN1 to IN3 = 3 V 10, 11, 12 IN1 to IN3 = 0.4V
* LED drive (Ta = +25 C, VB = 3.6 V) Value Unit Min. Typ. Max. 0.2 0.2 0.2 0.4 0.4 0.4 10 V V V A
Parameter
Symbol VLE1
Pin No. 2 4 1 2, 4, 1
Conditions LEDO1 = 25 mA LEDO2 = 25 mA LEDR = 25 mA VB = VO1 to VO3 = 6 V
Output voltage LED drive Output leakage current
VLE2 VLER ILEAK
17
MB3892
* Charge control (Ta = +25 C, EXTVCC = 5.2 V) Value Unit Min. Typ. Max. 0.8 EXTVCC - 0.5 0.85 1.85 18.8 1.35 1.35 1.0 1.8 1.44 2.44 20.8 1.43 1.43 2.0 2.5 0.1 5 2.15 3.15 22.8 1.52 1.52 5.0 10 2.2 V V
Parameter Control input range Control output minimum voltage Control output maximum voltage Charge control Control input current Control output voltage
Symbol VCHG VCOL
Pin No. 49 50
Conditions EXTVCC = 6 V EXTVCC = 6 V CHGV = 4 V VB = 4 V, CHGV = 1.59 V VB = 4 V, CHGV = 1.69 V 20 log{ (VGG2 - VGG1) / 0.1} VB = 3.6 V VB = 3.6 V EXTVCC = 6 V VB = VBH = 4 V, EXTVCC = 0 V Low precision VB = VBH = 3.6 V Low precision VB = 3.6 V, VBH = 3.75 V High precision VB = VBH = 3.6 V High precision VB = 3.6 V, VBH = 3.75 V 20 log{ (VCUR1 - VCUR2) / 0.15} 20 log{ (VCUR3 - VCUR4) / 0.15}
VCOH
50
V A V V dB V V V A V
ICHGV VGG1 VGG2 VGG VBATT VCHGBAT VBH ILBH VCUR1
49 50 50 50 48 44 46 46 47
Control gain BATT detected voltage VBH input voltage range VBH input leakage current
Charge current detector
VCUR2 Chage control output voltage
47
1.05
1.25
1.45
V
VCUR3
47
1.8
2.0
2.2
V
VCUR4
47
0.48
0.8
1.12
V
Current detected sensitivity
VCURG1 VCURG2
47 47
12 16
14 18
16 20
dB dB
(Continued)
18
MB3892
(Continued)
Parameter Symbol Pin No. 28, 34, 45, 58, 70, 74, 80 28, 34, 45, 58, 70, 74, 80 54 54 51 51 Conditions (Ta = +25 C, EXTVCC = 5.2 V) Value Unit Min. Typ. Max. 2.5 2.6 2.7 V
VB1 Switching voltage Preliminary of charge current charge circuit Charge current Exterenal power supply detector
VB2 IB1 IB2 VCDL VCDH
EXTVCC = 2 V, CHGDET = 0 A EXTVCC = 0.6 V, CHGDET = 0 A
3.8 40 80 OUT1 - 0.2
4.0 50 100 OUT1
4.2 60 120 0.3
V mA mA V V
CHGDET output voltage
* Serial control (Ta = +25 C, VB = 3.6 V) Value Unit Min. Typ. Max. 0 OUT1 x 0.7 -1 -1 OUT1 x 0.3 OUT1 1 1 V V A A
Parameter
Symbol VIL
Pin No. 6, 7, 8 6, 7, 8 6, 7, 8 6, 7, 8
Conditions DAT = SCLK = STBIN = 0 V DAT = SCLK = STBIN = 2.85 V
Input voltage Serial control Input current VIH IIL IIH
* Special power off (Ta = +25 C, VB = 3.6 V) Value Unit Typ. Max. VB VB x 0.3 V V
Parameter Special power off Output voltage
Symbol VIPOFF
Pin No. 59 59
Conditions IPOFF = 0 A
Min. VB - 0.1
IPOFFmode VRELEASE release voltage
19
MB3892
s TYPICAL CHARACTERISTICS
Power supply current vs. power supply voltage Power supply current IB (A)
Ta = + 25 C 200 150 100 50 0 0 1 2 3 4 5 6
Reference voltage vs. power supply voltage Reference voltage VREF (V)
1.4 1.2 1 0.8 0.6 0.4 0.2 0 0 1 2 3 4 5 6 Ta = +25 C VREF = 1 F
250
Power supply voltage VB (V)
Power supply voltage VB (V)
Reference voltage vs. ambient temperature
1.27 1.26
Output voltage vs. ambient temperature (BBREG2)
2.91
Output voltage VO2 (V)
VB = 3.6 V VREF = 1 F
VB = 3.6 V
2.89 2.87 2.85 2.83 2.81 2.79 -50
Reference voltage VREF (V)
1.25 1.24 1.23 1.22 1.21 1.2 1.19 -50 -25 0 25 50 75 100
-25
0
25
50
75
100
Ambient temperature Ta ( C) Output voltage vs. power supply voltage (BBREG1)
5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 1 2 3 4 5 6 Ta = +25 C OUT1 = 10 F
Ambient temperature Ta ( C) Output voltage vs. power supply voltage (BBREG2)
5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 1 2 3 4 5 6 Ta = +25 C OUT2 = 10 F
Output voltage VO1 (V)
Output voltage VO2 (V)
Power supply voltage VB (V)
Power supply voltage VB (V)
(Continued)
20
MB3892
Output voltage vs. power supply voltage (BBREG3)
5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 1 2 3 4 5 6 Ta = +25 C OUT3 = 2.2 F
Output voltage vs. power supply voltage (BATTREG) Output voltage VBATT (V)
5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 1 2 3 4 5 6 Ta = +25 C BATTOUT = 10 F
Output voltage VO3 (V)
Power supply voltage VB (V)
Power supply voltage VB (V)
Output voltage vs. power supply voltage (RFREG1)
5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 1 2 3 Ta = +25 C RFOUT1 = 2.2 F RFCTL1 = VB
Output voltage vs. control voltage (RFREG1)
5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 1 2 3 Ta = +25 C VB = 3.6 V RFOUT1 = 2.2 F
Output voltage VO1 (V)
4
5
6
Output voltage VO1 (V)
4
5
6
Power supply voltage VB (V)
Control voltage VRFCTL1 (V)
Output voltage vs. input voltage (Variable REG)
5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 1 2 Ta = +25 C VREGOUT = 10 F
Input current vs. input voltage (Variable REG)
200 180 160 140 120 100 80 60 40 20 0 0 1 2 Ta = +25 C VREGOUT = 10 F
Output voltage VO (V)
3
4
5
Input current IIN (A)
3
4
5
Input voltage VIN (V)
Input voltage VIN (V)
(Continued)
21
MB3892
DA1 output voltage vs. output current
0.5 0.45 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 0
DA1 output voltage vs. output current Output voltage VDAOUT1 (V)
3.6 3.4 3.2 3 2.8 2.6 2.4 2.2 2 1.8 1.6 0
Output voltage VDAOUT1 (V)
Ta = +25 C VB = 3.6 V D/AREF = VREF Digital input ALL"L"
Ta = +25 C VB = 3.6 V D/AREF = VREF Digital input ALL"H"
0.4
0.8
1.2
1.6
2
-0.2
-0.4
-0.6
-0.8
-1
Output current IDAOUT1 (mA)
Output current IDAOUT1 (mA)
DA4 output voltage vs. output current
0.5 0.45 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 0
DA4 output voltage vs. output current
3.6 3.4 3.2 3 2.8 2.6 2.4 2.2 2 1.8 1.6 0
Output voltage VDAOUT4 (V)
Output voltage VDAOUT4 (V)
Ta = +25 C VB = 3.6 V D/AREF = VREF Digital input ALL"L"
Ta = +25 C VB = 3.6 V D/AREF = VREF Digital input ALL"H"
0.4
0.8
1.2
1.6
2
-0.2
-0.4
-0.6
-0.8
-1
Output current IDAOUT4 (mA)
Output current IDAOUT4 (mA)
Power supply voltage VB (V)
Output voltage VO1 (V)
2 0
OUT1 4 RESET 2 0 0 10 20 30 40 50 60 70 80 90 100
2.6
2.65
2.7
2.75
2.8
2.85
2.9
REG1 Output voltage VO1 (V)
t (ms)
(Continued)
22
Reset input voltage VRESET (V)
5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0
4 2 0 VREF 4 VB Ta = +25 C VB = 0 V 3.6 V OUT1 = 10 F VREF = 1 F RESET = 50 pF CTP = 0.1 F RESETIN = 1000 pF
Output voltage VRESET (V)
Ta = +25 C
2 1 0
Reference voltage VREF (V)
Reset output voltage vs. REG1 output voltage
Hold time for power-on-reset
MB3892
Power supply voltage detected output voltage vs. power supply voltage
5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 1 2 3 4 Ta = +25 C
Power supply voltage detected output voltage vs. power supply voltage
5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 2.5 2.6 2.7 2.8 2.9 Ta = +25 C
Output voltage V3VDET (V)
Output voltage V3VDET (V)
5
6
3
3.1 3.2 3.3 3.4 3.5
Power supply voltage VB (V) Total harmonic distortion rate vs. output power (receiver Amp.) Total harmonic distortion rate THD (%)
100 Ta = +25 C V30R = 2.85 V OUTA to OUTB = 32 10 f = 1 kHz
Power supply voltage VB (V) Total harmonic distortion rate vs. output power (receiver Amp.) Total harmonic distortion rate THD (%)
100 Ta = +25 C V30R = 3.6 V OUTA to OUTB = 32 10 f = 1 kHz
1
1
0.1
0.1
0.01 0.001
0.01
0.1
1
0.01 0.001
0.01
0.1
1
Output power PO (W)
Output power PO (W)
Total harmonic distortion rate vs. output power (Loudspeaker Amp.)
100
Total harmonic distortion rate vs. output power (Loudspeaker Amp.) Total harmonic distortion rate THD (%)
100 Ta = +25 C V30R = 3.6 V SPOUTA to SPOUTB = 8 10 f = 1 kHz
Total harmonic distortion rate THD (%)
Ta = +25 C V30R = 2.85 V SPOUTA to SPOUTB = 8 10 f = 1 kHz
1
1
0.1
0.1
0.01 0.001
0.01
0.1
1
0.01 0.001
0.01
0.1
1
Output power PO (W)
Output power PO (W)
(Continued)
23
MB3892
Sounder1 output voltage vs. output current
0.5 0.45 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 Ta = +25 C VB = 3.6 V IN1 = IN2 = IN3 = "H"
Sounder2 output voltage vs. output current
0.5 0.45 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 Ta = +25 C VB = 3.6 V IN1 = IN2 = IN3 = "H"
Output voltage VO1 (V)
0
25
50
75 100 125 150 175 200 225 250
Output voltage VO2 (V)
0
20
40
60
80 100 120 140 160 180 200
Output current IO1 (mA) Sounder3 output voltage vs. output current
0.5 0.45 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 Ta = +25 C VB = 3.6 V IN1 = IN2 = IN3 = "H"
Output current IO2 (mA) LEDR output voltage vs. output current
0.5 0.45 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 Ta = +25 C VB = 3.6 V EXTVCC = 6 V
0
10
20
30
40
50
60
70
80
90 100
Output voltage VLER (V)
Output voltage VO3 (V)
0
5
10
15
20
25
30
35
40
45
50
Output current IO3 (mA)
Output current ILER (mA)
LED1 output voltage vs. output current
0.5 0.45 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 Ta = +25 C VB = 3.6 V
LED2 output voltage vs. output current
0.5 0.45 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 Ta = +25 C VB = 3.6 V
Output voltage VLE1 (V)
0
5
10
15
20
25
30
35
40
45
50
Output voltage VLE2 (V)
0
5
10
15
20
25
30
35
40
45
50
Output current ILE1 (mA)
Output current ILE2 (mA)
(Continued)
24
MB3892
CHGOUT output voltage vs. CHGV input voltage
6 Ta = +25 C 5.5 VB = 4 V 5 EXTVCC = 5.2 V 4.5 CHGBAT = OPEN 4 3.5 3 2.5 2 1.5 1 0.5 0 1.2 1.4 1.6
CHGOUT output voltage vs. CHGV input voltage
6 5.5 5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0
Output voltage VCHGOUT (V)
Output voltage VCHGOUT (V)
Ta = +25 C VB = 4 V EXTVCC = 5.2 V CHGBAT = CHGV
1.8
2
2.2
1
2
3
4
5
Input voltage VCHGV (V)
Input voltage VCHGV (V)
CHGI output voltage vs. VBH input voltage
2.5
CHGI output voltage vs. VBH input voltage
2.5
Output voltage VCHGI (V)
Output voltage VCHGI (V)
2 1.5
Ta = +25 C VB = 3.6 V EXTVCC = 5.2 V
2 1.5 1 0.5 0 0 1 2
Ta = +25 C VB = VBH - 0.15 V EXTVCC = 6 V
High precision
Low precision
1
High precision
0.5 0 3.5
3.6
3.7
3.8
3.9
4
4.1
4.2
3
4
5
Input voltage VBH (V)
Input voltage VBH (V)
Preliminary charge current vs. VB power supply voltage
-150 Ta = +25 C EXTVCC = 5.2 V 5.2 V
Charge current IB (mA)
-125 -100 -75 -50 -25 0 0 0.5 1 1.5 2 2.5 3
EXTVCC VA EXTS VB
6.2
IB 3.5 4 4.5 5
VB
VB power supply voltage VB (V)
(Continued)
25
MB3892
(Continued)
CHGDET output voltage vs. EXTVCC power supply voltage
5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 0.5 1 1.5 2 2.5 3
Power dissipation vs. ambient temperature Power dissipation PD (mW)
1600 1420 1400 1200 1000 800 600 400 200 0 -40 -20 0 20 40 60 80 100
Output voltage VCHGDET (V)
Ta = +25 C VB = 3.6 V
3.5
4
4.5
5
EXTVCC power supply voltage VEXTVCC (V)
Ambient temperature Ta ( C)
26
MB3892
s FUNCTIONAL DESCRIPTION
1. Power Control
(1) Reference voltage This circuit uses the voltage generated by VB1 terminal (pin 28) to produce a temperature compensated reference voltage (1.23 V typ.) for power control and uses this reference voltage on power control. (2) Baseband regulator (BBREG1) This regulator uses the reference voltage to produce an output voltage (2.85V typ.) at OUT1 terminal (pin 75). Power can be drawn from OUT1 terminal for external use, up to a maximum load current of 110 mA. (3) Baseband regulator (BBREG2) This regulator uses the reference voltage to produce an output voltage (2.85 V typ.) at OUT2 terminal (OUT21 terminal (pin 72), OUT2-2 terminal (pin73)). Power can be drawn from OUT2 terminal for external use, up to a maximum load current of 150 mA. (4) Baseband regulator (BBREG3) This regulator uses the reference voltage to produce an output voltage (2.85V typ.) at OUT3 terminal (pin 71). Power can be drawn from OUT3 terminal for external use, up to a maximum load current of 60mA. (5) Battery backup regulator (BATTREG) This regulator uses the reference voltage to produce an output voltage (3.1V typ.) at BATTOUT terminal (pin 69). (6) Vibrator drive circuit (VIBREG) This circuit uses the reference voltage to produce an output voltage (1.5V typ.) at VIBREG terminal (VIBREG1 terminal (pin 78), VIBREG-2 terminal (pin 79)). Power can be drawn from VIBREG terminal for external use, up to a maximum load current of 200mA. (7) RF regulator (RFREG1) This regulator uses the reference voltage to produce an output voltage (2.85V typ.) at RFOUT1 terminal (pin 42) when an "H" level signal is input at the RFCTL1 terminal (pin 41). Power can be drawn from RFOUT1 terminal for external use, up to a maximum load current of 10mA. (8) RF regulator (RFREG2) This regulator uses the reference voltage to produce an output voltage (2.85V typ.) at RFOUT2 terminal (pin 40) when an "H" level signal is input at the RFCTL2 terminal (pin 39). Power can be drawn from RFOUT2 terminal for external use, up to a maximum load current of 20mA. (9) RF regulator (RFREG3) This regulator uses the reference voltage to produce an output voltage (2.85V typ.) at RFOUT3 terminal (pin 38) when an "H" level signal is input at the RFCTL3 terminal (pin 37). Power can be drawn from RFOUT3 terminal for external use, up to a maximum load current of 20mA.
27
MB3892
(10) RF regulator (RFREG4) This regulator uses the reference voltage to produce an output voltage (2.85V typ.) at RFOUT4 terminal (pin 35) when an "H" level signal is input at the RFCTL4 terminal (pin 36). Power can be drawn from RFOUT4 terminal for external use, up to a maximum load current of 60mA. (11) RF regulator (RFREG5) This regulator uses the reference voltage to produce an output voltage (2.85V typ.) at RFOUT5 terminal (RFOUT5-1 terminal (pin 30), RFOUT5-2 terminal (pin 29)) when an "H" level signal is input at the RFCTL5 terminal (pin 31). Power can be drawn from RFOUT5 terminal for external use, up to a maximum load current of 200mA. (12) RF regulator (RFREG6) This regulator uses the reference voltage to produce an output voltage (2.85V typ.) at RFOUT6 terminal (pin 33) when an "H" level signal is input at the RFCTL6 terminal (pin 32). Power can be drawn from RFOUT6 terminal for external use, up to a maximum load current of 50mA. (13) Variable bias regulator This regulator uses the voltage generated by VREGIN terminal (pin 67) to produce an amplified output voltage at VREGOUT terminal (pin 68). Power can be drawn from VREGOUT terminal for external use, up to a maximum load current of 10mA. (14) D/A converter D/A1 to D/A3 converter process 8 bit input signal and D/A4 converter processes 10 bit input signal. This converter generates an output voltage (0.5 to 2.5V ) at D/AOUT1 terminal (pin 63) to D/AOUT4 terminal (pin 60) according to the signal from serial control. (15) Power-on reset When the OUT1 terminal (pin 75) voltage exceeds 2.75V(typ.) , after a delay interval set by a capacitor (0.1 F typ.) connected to the CTP terminal (pin 76) , the RESET terminal (pin 77) voltage becomes "H" level from "L" level and the reset signal is canceled. When the OUT1 terminal voltage falls below 2.685V (typ.), the RESET terminal voltage becomes "L" level from "H" level and the reset signal is dispatched. (refer to "sPOWER-ON RESET TIMING DIAGRAM", "sSETTING OF HOLD TIME FOR POWER-ON RESET".) (16) Battery voltage detect This function is to observe the battery voltage. When the VB4 terminal (pin 58) voltage exceeds 3.05V (typ.), the 3VDET terminal (pin 56) voltage goes to "H" level and when the VB4 terminal voltage falls below 2.85V (typ.), the 3VDET terminal goes to "L" level. (refer to sBATTERY VOLTAGE DETECTOR)
28
MB3892
2. Speaker Amp.
(1) Receiver Amp. This is the BTL output type Amp. driving speaker directly. When the output power is 90mW typ. (at 32), the serial control processes the on/off and the earphone switching control. The optional gain can be set by the connection of feedback resistor from FB terminal (pin 20) to OUTA terminal (pin 25) and the connection of input resistor to FB terminal. (2) Loudspeaker Amp. This is the BTL output type Amp. driving speaker directly. When the output power is 260mW typ. (at 8), the serial control processes the on/off control. The optional gain can be set by the connection of feedback resistor from FB terminal (pin 20) to SPOUTA terminal (pin 22) and the connection of input resistor to FB terminal.
3. Sounder
Three low-saturation output transistors are built in for buzzer drive. When the signal from serial control is "H" level and IN1 terminal (pin 10) voltage is "H" level, the V01 terminal (pin 16) voltage is 0.3V (typ.). When IN2 terminal (pin 11) voltage and IN3 terminal (pin 12) voltage are "H" level, the V02 terminal (pin 14) voltage and V03 terminal (pin 13) voltage are also 0.3V (typ.).
4. LED drive
The LEDO1 terminal (pin 2) voltage and LEDO2 terminal (pin 4) voltage is 0.2V (typ.), when the signal from serial control is "H" level. When the signal from charge control is "H" level, the LEDR terminal (pin 1) voltage is 0.2V (typ.).
5. Charge control
(1) Charge control The main charge is started by the signal from serial control indicates preliminary charge is finished. According to the voltage level at CHGV terminal (pin 49) generated by microprocessor on the microprocessor operation, the charge current is controlled by adjusting gate voltage from outside FET. (2) Charge current detector The charge current detector sensitivity (gain) can be switched by the signal from serial control. The VBH terminal (pin 46) voltage and VB4 terminal voltage (pin 58) are detected and CHGI terminal (pin 47) voltage is generated. (3) Preliminary charge circuit When the battery voltage is low, the charge is controlled until the microprocessor starts the operation. Before the battery voltage reaches 2.6V (typ.), 50mA (typ.) is used for the charge and before 4V (typ.), 100mA (typ.) is used. (4) External power supply detector This function is to detect if the case is attached to the battery charger. When the case is attached to the battery charger, EXTVCC terminal (pin 52) voltage is "H" level and generate "L" level voltage at CHGDET terminal (pin 51). When the case is not attached to the battery charger, EXTVCC terminal voltage is "L" level and generate "H" level voltage at CHGDET terminal. 29
MB3892
6. Serial control
After the input signal from microprocessor at DAT terminal (pin 6) is captured at the rising edge of SCLK terminal (pin 7), the signal is input in the internal register at the rising edge of STBIN terminal (pin8) and mode is set.
7. Special power off
This function can control the power consumption current of main IC under 11A (typ.) and the battery can be kept for the long period under the conditions that battery package is attached to the mobile phone on the shipment.
30
MB3892
s CONDITIONS of EACH REGULATORS at MEASUREMENT of CONSUMPTION CURRENT
Each regulators conditions at the measurment of consumption current are as the following table. [BIASSW] siganl of serial control is "H" level (BIASSW OFF) . BBREG1 BBREG2 BBREG3 BATTREG Special power off Standby Power on (waiting/intermittent) Power on (waiting/receiving) Power on (conversation/ transmission) IB1 IB2 IB3 IB4 OFF ON ON ON OFF OFF OFF ON OFF ON ON ON OFF ON ON ON VIBREG VARREG RFREG1 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON
IB5
ON
ON
ON
ON
OFF
OFF
ON
Power on IB6 (conversation/receiving)
ON
ON
ON
ON
OFF
OFF
ON
RFREG2 RFREG3 RFREG4 RFREG5 RFREG6 Special power off Standby Power on (waiting/intermittent) Power on (waiting/receiving) Power on (conversation/ transmission) Power on (conversation/ receiving) IB1 IB2 IB3 IB4 OFF OFF OFF ON OFF OFF OFF ON OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON
Receiver Loudspeaker Amp. Amp. OFF OFF OFF OFF OFF OFF OFF OFF
IB5
ON
OFF
OFF
ON
ON
ON
OFF
IB6
ON
ON
ON
OFF
ON
ON
OFF
31
MB3892
s LOGICS
(1) Serial Control Setting Table A7 1 A6 1 A5 1 D9 Data
PDSP
A4 1
A3 1 D8
PDRCV
A2 1 D7
A1 1
A0 0 D6 D5 D4 D3 D2
VIBCTL VIB REGON
D1
D0
CHOISE BTL drive
LEDC1 LEDC2 (green) (red) ON OFF 0 ON OFF 0
BIASSW REG2CTL OFF ON 0 OFF ON 0
LEDRCTL VREGCTL
Charge red Variable LEDOFF REGON
Operation Loud at data "1" AMPON
Receiver AMPON
Operation Loud Receiver Single at data "0" AMPOFF AMPOFF drive
Initial value after reset 0 0 0
VIB Charge red Variable REGOFF LEDON REGOFF 0 0 0
A7 1
A6 1
A5 1 D9
A4 1
A3 1 D8
A2 1 D7
A1 0
A0 1 D6 D5
CHGISE L
D4
D3
D2
D1
D0
Data
REG3CTL
PWOFFCTL
PRCHG BUZZSEL SOUND1 SOUND2 SOUND3 OFF
Loudspeaker PRCHG Sounder1 Sounder2 Sounder3 Amp. short ON ON ON OFF waveform output Loudspeaker PRCHG Amp. ON usual output
Operation at data "1"
Special REG3ON REG3OFF power off setting
Low precision
Operation REG3OFF REG3ON at data "0"
Initial value after reset
High Special power off precision ( x 8) setting 1 0
Sounder1 Sounder2 Sounder3 OFF OFF OFF
1
0
0
0
0
0
0
0
: Unused
32
MB3892
A7 1 A6 1 A5 1 D9 Data Operation at data "1" Operation at data "0" Initial value after reset 0 0 0 0 A4 1 A3 1 D8 A2 1 D7 A1 0 A0 0 D6 D5 D4 D3 D2 D1 D0
DAR4_9 DAR4_8 DAR4_7 DAR4_6 DAR4_5 DAR4_4 DAR4_3 DAR4_2 DAR4_1 DAR4_0
DA4 setting data
0
0
0
0
0
0
A7 1
A6 1
A5 1 D9
A4 1
A3 1 D8
A2 0 D7
A1 1
A0 1 D6 D5 D4 D3 D2 D1 D0
Data Operation at data "1"
PDNDA4 PDNDA3 DAR3_7 DAR3_6 DAR3_5 DAR3_4 DAR3_3 DAR3_2 DAR3_1 DAR3_0 DA4ON DA3ON DA3 setting data
Operation DA4OFF DA3OFF at data "0"
Initial value after reset
0
0
0
0
0
0
0
0
0
0
A7 1
A6 1
A5 1 D9
A4 1
A3 1 D8
A2 0 D7
A1 1
A0 0 D6 D5 D4 D3 D2 D1 D0
Data Operation at data "1" Operation at data "0" Initial value after reset :Unused

PDNDA2 DAR2_7 DAR2_6 DAR2_5 DAR2_4 DAR2_3 DAR2_2 DAR2_1 DAR2_0 DA2ON DA2 setting data DA2OFF 0 0 0 0 0 0 0 0 0
33
MB3892
A7 1
A6 1
A5 1 D9
A4 1
A3 1 D8
A2 0 D7
A1 0
A0 1 D6 D5 D4 D3 D2 D1 D0
Data Operation at data "1" Operation at data "0"
Initial value after reset

PDNDA1 DAR1_7 DAR1_6 DAR1_5 DAR1_4 DAR1_3 DAR1_2 DAR1_1 DAR1_0 DA1ON DA1setting data DA1OFF 0 0 0 0 0 0 0 0 0
A7 1
A6 1
A5 1 D9
A4 1
A3 1 D8
A2 0 D7
A1 0
A0 0 D6 D5 D4 D3 D2 REG3CTL D1 Special power off setting D0
Data Operation at data "1"

PWOFFCTL Special power off setting 1
REG3ON
Operation at data "0"
Initial value after reset

REG3OFF

1
0
:Unused
34
MB3892
(2) Input Signal Timimg Parameter Data setup time Data hold time STB setup time STB pulse duration Removal time (3) Input Signal Timing Diagram (Input voltage "H" level = 2.85 V, "L" level = 0 V) Symbol tsc thc tss tds ths Value Min. 100 100 100 100 100 Typ. Max. Unit ns ns ns ns ns Remark
tsc
SCLK
50
DAT
A7
A6
A5
A4
D1
D0
thc tss ths 50
STBIN
tds
Note : Data is defined at the rising edge of SCLK and IC mode is set through latching of DAT at rising edge STBIN.
35
MB3892
s POWER-ON RESET TIMING DIAGRAM
OUT1
2.75 V 2.685 V
CTP
1.23 V
TPR
TPR 90 % tr 10 % (3) (4) (5) 90 % tf 10 % (6)
RESET
90 % tr 10 % (1) (2) 90 % tf 10 %
(1) When the OUT1 terminal (pin 75) voltage exceeds detected rising voltage (2.75V typ.), the charge for timing capacitor (CTP) for hold time for power-on reset starts . (2) When the CTP terminal (pin 76) voltage exceeds 1.23V (typ.), the reset is canceled. (The RESET terminal voltage becomes "H" level from "L" level.: rising time from 10% to 90% = tr) (3) When OUT1 terminal voltage falls below detected rising voltage (2.685V typ.), the CTP terminal voltage is down and the reset signal is output. (RESET terminal voltage becomes "L" level from "H" level.) (4) When OUT1 terminal voltage exceeds rising voltage detect, charging of CTP is started. (5) When CTP terminal voltage rises above threshold voltage, the reset is canceled. (6) When OUT1 terminal voltage falls below the voltage detect, the reset signal is output.
s SETTING OF HOLD TIME FOR POWER-ON RESET
According to the time constant set by capacitor (CTP) connected to CTP terminal (pin 76), rise time (hold time) of RESET terminal (pin 77) voltage can be set after OUT1 terminal (pin 75) voltage exceeds 2.75V (typ.). 1.23 (V) x CTP (F) 1.75 (A)
POR hold time : TPR (s) = :
(tr of RESET is not included)
36
MB3892
s RISE TIME FOR SPEAKER Amp.
BP = 4.7 F BP = 4.7 F
TR BP 1.0 V
1.6 V BP
TR 1.0 V
1.6 V
Speaker output
+
Speaker output
-
BTL drive Rise time TR (ms) = 10.3 (k) x CBP (F) :
Single drive (Earphone mode)
s PRELIMINARY CHARGE CURRENT
Charge current (mA)
100
50
0
2.6
4
VB (V)
s BATTERY VOLTAGE DETECTOR
3VDET (V) 2.85
0 0 2.85 3.05 VB (V)
37
MB3892
s USAGE PRECAUTIONS
* Printed circuit board ground lines should be set up with consideration for common impedance. * Take appropriate static electricity measures.
* * * * Containers for semiconductor materials should have anti-static protection or be made of conductive material. After mounting, printed circuit boards should be stored and shipped in conductive bags or Containers. Work platforms, tools, and instruments should be properly grounded. Working personal should be grounded with resistance of 250 k to 1 M between body and ground.
* Do not apply negative voltages
The use of negative voltages below -0.3V may create parasitic transistors on LSI lines, Which can cause abnormal operation.
s ORDERING INFORMATION
Part number MB3892PFF Package 80-pin plastic LQFP (FPT-80P-M17) Remarks
38
MB3892
s PACKAGE DIMENTION
80-pin plastic LQFP
(FPT-80P-M17)
12.000.20(.472.008)SQ 10.000.10(.394.004)SQ
60 41
(1.40(.055))
61
40
Details of "A" part (11.00(.433))
0.10(.004) 0.100.05 (.004.002)
80
21
"A" 0.500.10 (.020.004) 22
1
20
0.160.04 (.006.002)
0.40(.016) TYP
0.127 -0 +.002 .005 -0
+0.05
1.500.10 (.059.004)
C
1999 FUJITSU LIMITED F80031SC-1-1
Dimansions in mm (inches) .
39
MB3892
FUJITSU LIMITED
For further information please contact: Japan FUJITSU LIMITED Corporate Global Business Support Division Electronic Devices KAWASAKI PLANT, 4-1-1, Kamikodanaka, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8588, Japan Tel: +81-44-754-3763 Fax: +81-44-754-3329 http://www.fujitsu.co.jp/ North and South America FUJITSU MICROELECTRONICS, INC. 3545 North First Street, San Jose, CA 95134-1804, U.S.A. Tel: +1-408-922-9000 Fax: +1-408-922-9179 Customer Response Center Mon. - Fri.: 7 am - 5 pm (PST) Tel: +1-800-866-8608 Fax: +1-408-922-9179 http://www.fujitsumicro.com/ Europe FUJITSU MICROELECTRONICS EUROPE GmbH Am Siebenstein 6-10, D-63303 Dreieich-Buchschlag, Germany Tel: +49-6103-690-0 Fax: +49-6103-690-122 http://www.fujitsu-fme.com/ Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE. LTD. #05-08, 151 Lorong Chuan, New Tech Park, Singapore 556741 Tel: +65-281-0770 Fax: +65-281-0220 http://www.fmap.com.sg/ Korea FUJITSU MICROELECTRONICS KOREA LTD. 1702 KOSMO TOWER, 1002 Daechi-Dong, Kangnam-Gu,Seoul 135-280 Korea Tel: +82-2-3484-7100 Fax: +82-2-3484-7111
All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document are presented as examples of semiconductor device applications, and are not intended to be incorporated in devices for actual use. Also, FUJITSU is unable to assume responsibility for infringement of any patent rights or other rights of third parties arising from the use of this information or circuit diagrams. The contents of this document may not be reproduced or copied without the permission of FUJITSU LIMITED. FUJITSU semiconductor devices are intended for use in standard applications (computers, office automation and other office equipments, industrial, communications, and measurement equipments, personal or household devices, etc.). CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.) are requested to consult with FUJITSU sales representatives before such use. The company will not be responsible for damages arising from such use without prior approval. Any semiconductor devices have inherently a certain rate of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Control Law of Japan, the prior authorization by Japanese government should be required for export of those products from Japan.
F0007 (c) FUJITSU LIMITED Printed in Japan

▲Up To Search▲

Price & Availability of MB3892

	To Download MB3892 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .